FJ Software

Give me an example number in your Country in local format and in international format, you can XXX the last three digits.

Beside that problem, i have a problem with time of call. Every call is registrated 2 hours before real time. Is there a way to fix this?

Ensure that the "Region" setting in your phone does match with your timezone settings on the PC

when you're inland you can dial

098 123456
098 1234567
091 1234567
092 1234567

for mobile lines, or for land lines:

01 1234567
042 1234567
052 1234567

However, when you're outside the country, you have to dial country code +385. So it is:

+385 98 123456
+385 98 1234567
+385 91 1234567
+385 92 1234567

for mobile lines, or for land lines:

+385 1 1234567
+385 42 1234567
+385 52 1234567

All my contacts are saved with national code "+385" because I can dial this when I'm home and in other country, the same.
So it looks like +385911234567

If I want to dial only from my country, I can save it simply like
0911234567

The problem is "0" in the end of all 7digit numbers (+385911234567"0" or 0911234567"0")
If number is 6 digit, then it is displayed okay (+38598123456 or 098123456).

About time of call....

My time zones were okay on both sides. Check the pictures.
Is this the same as "region"? If not, how do I reach the settings for region? What else can i do?

If I call from MPE, time of call is okay. But when I sync for other calls, it is always "-2hrs".

And it happen only in SYNC, when I handle calls directly through MPE it is ok.

Where does the "0" at the end of the number come from ?

Time diffrence: Which model you are using ? Please check if there is a setting called "Region" in your phone, often its a littlebit hidden behind the "More" button.

That is my question for you. Zero is generated by MPE after sync call list. But MPE still recognizes this number and assign name from the phone book to it. But if I want to use the number itself, I get error from operator of course.

I found "region" setting in my Cedar. You're right, it was hidden behind soft button. And i had to disable automatic time update to set it. But it didn't change anything. I'm still getting -2hrs in MPE when I sync calls.
My GMT is and was +1. Same as yours.

Same problem again! MPE 1.8.4 - The phone number being used it IS NOT part of the phone's addressbook

Zero is generated by MPE after sync call list.

In this case its not an issue of MyPhoneExplorer. The call list does show exactly the numbers how they were read from the call log of the phone.

@blutarsky: Where is the image ?

Here

OK, will be fixed

blutarsky965 hat geschrieben:It looks like MPE is randomly adding a leading zero when grouping numbers....
Number sample (hiding last 3 digits here for privacy)

1) 03339139... (leading 0)
2) 3339139... (no leading 0)

See the follwing image

how to make conversation view in mpe like seen in the above images any one tell me

In the left column of MyPhoneExplorer, in the Messages box, click on Conversation

i didnt find tat option only having inbox,drafts,sentitem,saved and archive where it is

where is tat option conversation view

BugMeNot hat geschrieben:where is tat option conversation view

Should be above Inbox.

Do you have current MPE version 1.8.4?


Best regards and Merry Chrismas.

i didnt find that option see below image using 1.8.4 version

i didnt find tat option where is that option converstaion view

If this point is not shown, i think it's not supported by your phone or by interface.

best regards...

is it not suitable for sony w300 and k800, what is interface

is it not suitable for sony w300 and k800, what is interface

reply me then i will not post in this thread